|
So rather than trusting the image I chose to trust the words and for this particular case that was the wrong choice. We have used the saw for a bathroom project and it worked very well. 1/10 Update.turns out Amazon advertised this item wrong and the company tried for months to get them to correct it and the company was great trying to help me get the whole mess cleaned up. I spent so much time looking at images and I found some of them to be different from the written description. 7/09 My review only pertains to the information in the ad, that sates; "Built-in, quick adjusting 45-degree miter system for less downtime." This is not true.
It took months and in the end Amazon did nothing, did not respond to me or to the company emails and we (the company and I figured out the best solution). The saw does not have this feature and it was one of the main reasons I purchased the saw. This would not be so upsetting if the MK miter cutting accessory didn't cost $55. About to start the second bathroom. So again just make sure you double check what you are going to get before placing your order.
Invest in some good ear plugs. I have owned 3 of these MK saws. They are great for working inside, but with one caveat. Joe They are loud when they are new, and they get louder as they age.
For the price it is a good deal. My nit-pic is that to cut a 16" tile, you need to tilt the tile into the saw blade because the distance to the backstop is 1/4 inch too short.
Clean the pump filter after every use. I have owned mine for eight years and have cut a lot of tile with it with no problems.I don't know if they are making it cheaper now, thus perhaps the problem the other reviewer had with failure. Sadly most of the tools we buy now are Chinese made junk imitations of once great tools. You can find this new on Ebay for under $200. Great saw, a couple tips: lube the slide tube with WD40 and keep it clean.
Having to refill the tray is the least of it, since the dirty water makes a mess in your work area.- When cutting large tiles (12" and up), some water pours off the top of the tile being cut onto the floor, to the right of the machine.- The guide rail gets dirty, which keeps the cutting table from sliding easily. The high motor speed and worm gearing is why the tool is loud. The worm gear design results in gear failure if the tool is under any serious stain, such as many hours of hard-tile cutting. - Sufficiently light to make transport by one person, easy.The bad:- Water flow to the blade was not sufficient in my estimation, so I slightly modified the water output ports near the blade to increase the flow. My tool failed within 20 hours of total use.This consumer-grade saw is an OK tool for the occasional do-it-yourselfer, as long as it's not used very much and you limit cutting of hard tiles (marble, granite, porcelain, concrete, etc). (It is used when you want to make several tiles of the same width).The ugly:- Toward the end of the bathroom tile job I did, the gears were making a very-noisy grinding sound. The blade no longer turned, rendering the tool useless. The opposing gear was also ruined.
You have to clean the filter to restore flow.- The aluminum `stop' accessory for the table is so crudely made; it is difficult to get it square to the table. The motor appears to turn in the 24,000-rpm range; which is reduced via its worm gear to around 3400 rpm at the blade. When those teeth are stressed beyond the design goal (minimal tool use and/or softer tiles), metal fatigue occurs; keep cutting, as with my bathroom job, and the gear teeth are worn down to the point the tool fails. It cuts very hard tile slowly, but on softer tile, it cuts quickly.- Relatively inexpensive for a wet saw.
At least it worked long enough to finish one big job.Summary:Why did the tool gears strip so quickly. - Lots of water is sprayed to the rear of the blade; M-K's water containment system doesn't work. The good:- Did a kitchen splash back job and a full-tile job for a bathroom -- 200 square feet of porcelain tile. Not a big deal, but it should work better.- The water pump clogs too quickly. Tried to use it for another small job after that, and the tool died completely. That is, the drive gear (shown in the photo) is only one-half inch in diameter, with 7 teeth in total, so no more than two teeth are fully engaged in the opposing gear at any time.
Probably due to the strain on the tool of cutting a large number of porcelain tiles (versus softer tiles). Even though this only took 20 minutes, this is not something a customer should have to do.- This tool is very loud; ear protection is needed; especially if used indoors. (Click on Customer Photos above to see the striped worm gear). Although brick and concrete pavers (e.g., 2" thick) can be cut with quality wet-saws, do not use this saw for that purpose, as those products would quickly ruin the worm gear. Unfortunately, my saw warranty had expired; and since the replacement parts were so expensive, the M-K saw was discarded.
|
