Freud FC-107 7-Piece Carbide Forstner Bit Set

• Freud FC-009 1-1/4-Inch by 3/8-Inch Shank Carbide Forstner Bit
• Freud FC-006 7/8-Inch by 3/8-Inch Shank Carbide Forstner Bit
• HTC HTC2000 Universal Mobile Base
• The Handplane Book
• Frozen River

About this 7-Piece Bit Set
The Freud 7-piece carbide forstner bit set features micro-grain carbide/titanium tips to ensure cleaner cuts and long lasting sharpness. Ideal for drilling exceptionally clean holes in veneers and thick stock, the bits come with a center spur that allows for easy and accurate location of the center of the pilot hole. Because the bits are guided by a super-sharp outside rim, the bits are able to precision bore overlapping holes and pocket holes. The bits can be re-sharpened, and can drill in all composition materials, plywood, hard wood, solid surface materials, and soft wood using hand-held drills and drill presses.

Applications
These bits drill all composition materials, plywoods, hardwoods, solid surface materials and softwoods. Use them in hand-held drills and drill presses.

Warranty
The bit set is covered by Freud's limited lifetime warranty.

Rebuilding from Hurricane and getting to use many of the new tools and these bits are well within the five star range for my money. First time working with the bits today and well satisfied, as usual, with the Freud products. Very sharp and smooth. You may pay a little more for the name, but the quality is there. Good buy.

Still recommend Freud blades and cutters. I work with a lot of hardwoods and you have to be careful about the pressure you use with HSS bits, so you don't burn your workpiece or overheat your bit. I have noticed no wobble in any of the bits and other than the sharpening problem have had no trouble with this set. I do think my HSS set does a little better job in soft wood and plywood, but it is a close call. They are usually ready to go out of the box. These are the first Freud cutter's I have had that were'nt sharp out of the box, so I won't let it influence my love of Freud blades and cutters in the future. I pulled it out of the drill press and upon examining the cutting edge, I noticed it did not have that bright, shiney edge you normally associate with a sharp tool.

I examined the rest of the bits and they looked the same. Cutting the last hole was as easy as cutting the first. So $30 and an hour later I was on my way home with sharp bits. I rated it 4 stars because of the sharpening problem. Wish I could afford some larger ones in carbide.3"-31/2" would be nice for clock making. I love Freud cutters and saw blades.

I chucked up the 3/8 bit to bore some holes for decorative plugs and noticed that the bit was not cutting a very clean hole, seemed like I had to apply too much pressure also. So I carried them down to the local saw shop where I get all my blades and cutters sharpened and ask them to take a look at the bits. I have a set of Freud HSS Forstner bits, and they are very good. I cut another 19 holes and each was excellent. I recieved this set as a gift and even though I already have these size's I was pretty excited to get a set of carbide bits. Their opinion was that the bits were very dull, looked like the last two steps in sharpening them had been overlooked.

This time the results were what I had hoped for.The bit cut thru the Padauk very nicely and left a nice clean hole. Put the 3/8 back in the drill press and tried again.

The carbide bits are very sharp and cut a very true hole. If I had to choose between the Freud carbide set and the Freud steel set, I would probably go with the steel, because it has 9 more bits. Instead I went with the 1-1/4" Freud steel forstner bit. The bits are very straight compared to the junky Irwin bits I got at Home Depot. I have been using the bits for several months.

The steel bit seems to work just as well as the carbide bits. I have had very good results working with soft woods on my small drill press. The only problem I have with this set is that it is missing several handy sizes such as 7/8", 1-1/8" & 1-1/4". Buying forstner bits individually can get very expensive. I tried to purchase the Freud 1-1/4" carbide bit on Amazon, but they appear to no longer stock them.

It had to be exchanged due toseveral chips in the carbide cutting edges. Overall the quality of the grinding on the carbide cutting tips and the body of the bit was uneven and poorly finished. For the money I expected more and returned these bits. This is my second experience with Freud cutting tools. My twenty year old hand sharpened steel bits produced better results.

The first was their 8 inch super dado set. The replacement has performed adequately. This forstner bit set produced disappointing results for the money. The surface of the workpiece had burrs where the bit first made contact and the interior of the hole showed a torn surface on the end grain side as opposed to a smooth cut.

The carbide edges offer much longer life between sharpenings. This set is worth the money for anyone serious about woodworking. These bits offer the most controlled cutting available when used with a drill press. Also the 1 3/8" size is perfect for european cup hinges. Especially usefull for cutting shallow or flat bottom mortises, partial circles laid over the edge of your stock, and holes drilled at an angle to the surface.